E-mail: info@fdsp-cn.com
Tel: +86-025-66621288-808

FDSP Brand Small Wood Pellet Project

Wood Pellet Project Brief Introduction

  1. Wood pellet project can produce flat-mode suppression of biomass particles.

  2. Our product using cold forming technology and cosmetic polishing process. It has beautiful appearance and compact structure.

  3. High output, low energy consumption, low noise, low failure, fatigue and strong machine, continuous production, economic and durable.

  4. The whole machine uses a special high-quality materials and advanced with shaft drive, the key components of high quality alloy steel plus wear-resistant material, the use of German Vacuum furnace heat treatment, to extend the service life 5-7 years.

 

wood pellet production line


Wood Pellet Project Working Principle 

  1. material go into the mode of the granulating chamber vertically using its own weight

  2. the pressure roller will press the raw material inside the mode holes

  3. under the continuous pressure of rollers

  4. material will be made into pellet 5. at last, wood pellet was sent to the material feeding mouth through scraper feeder.



Wood Pellet Project Application 

Wood Pellet Project mainly applicable to crude fiber granulation, such as: sawdust, rice husk, cotton see hull, weeds and all kinds of crop straw, home wastage, the worn out plastic and the factory reject, the material of low adhesion rate, difficult to forming. It also can be applied to biological fertilizer, organic fertilizer, compound fertilzer low temperature pelleting.

wood pellets


Wood Pellet Project Warranty

  1. Three-five Years (Calculated from the goods arrived the destination port.) If any parts (excluding easily damaging parts) are found defective in quality in the first year, we shall replace it free-of-cost. After one year, parts can be replaced on favorable payment basis.We can send our engineer to provide the installation and trial run in your place. But the relevant cost shall be bear in your account (round trip air ticket, board and lodging).

  2. Our professional service includes: Free training, Guidance Installation and Debugging.

  3. If you have any question, please contact us freely. Our after-sales service team on-line will do the best to accomplish your sincere requirement on time.


Pellet production line process:

(a)Peeling Process

Wood debarker machine is applicable to peel the log of MDF board and papermaking industry, it is mainly used to peel log, small wood and so on, the peeled rate is more than 95 percent.

 

(b)Chipping Process

In the pellet plant before raw materials are made into biomass pellets, they are first reduced into much 

smaller, uniformly-sized particles. When the thicknedd is larger than 10mm or the size is greater than 50*50mm, a chippper is needed to chip these materials into smaller pieces.

 


(c)Grinding Process

The hammer mill is used to further crush these small pieces into particles of less than 3mm in diameter.

 

 

(d)Drying Process

After raw materials are crushed a dryer is needed since most raw wood materials havea moisture content of about 50%. However, the optimal moisture content for pelletiztionis 13%-15%. Therefore a rotary dryer is included in the pellet plant to reduce the moisture content. After crushing and drying you can begin making wood pellets.

 


(e)Pelletizing Process

After crushing and drying the raw material properly it is then ready for the pellet mill. The pelletizing machine orpress is the key piece of machinery in the pellet plant. It should be mentioned that impurities in the raw materials like metal or stone,may damage the die and rollers of pellet making machine.

 

 

(f)Cooling Process

Usually after pelletizing, the temperature of pellets is between 60-80 degrees and the moisture content is close to 15%. For storage purpose, a cooler must be used to reduce their surface temperature and moisture content.

 

(g)Packing Process

 Finally is the packing process. In order to protect the wood pellets becoming getting 

damp and to increase storability, proper packing is necessary. 

 

Packing & Shipping

 

Packaging:  

Depending on customers' requirement,such as wooden box or Iron crate etc.

 

Shipping:     

Our shipping operator and delivering equipments will be ready on time to ensuregoods shipped based on Sales Order requirement.